Logmessage / Codes / Fehlercodes (Events, Eventcodes) der Flatcontrol an die TwinIP (fcserial)

Die folgenden Codes tauchen im technischen Log-File vom ProtectMaster auf. Es handelt sich um Event-Codes, welche die FLC (Flatcontrol) an die TwinIP, bzw. an die fcserial schickt. Hier die Liste, was jene Codes zu bedeuten haben…

fcserial FlatControlBusiness Software Interface

FlatControlBusiness_Software_Interface_V1_06

# Events und deren Tables

event2=Open{dev,bus,remote,info1:schlossPID}
event3=Close{dev,bus,remote,info1:schlossPID}
event4=Lock bolt opened{dev}
event5=Lock bolt closed{dev}
event6=System opened
event8=System closed
event9=System locked{remote}
event10=System unlocked{remote}
event13=Managercode has been changed{dev,remote,info1:schlossPID,info2:twinalarm}
event14=Mastercode has been changed{dev,remote,info1:schlossPID,info2:twinalarm}
event19=PIN-Code expired{dev,info1:schlossPID}
event20=Code ok{dev,bus,remote,info1:schlossPID,info2:codeType,info3:finger}
event24=PIN-Code has been changed{dev,remote,info1:schlossPID,info2:schlossPIDAdmin,info3:twinalarm}
event27=PIN-Code has been deleted{dev,remote,info1:schlossPID,info2:twinalarm}
event34=Date/time has been changed{remote}
event36=Time change
event37=RTC-Error
event47=Reset block period{info12:time}
event49=Time program termination{dev,remote}
event50=User locked{dev,remote,info1:schlossPID}
event62=Wrong lock{dev,bus,remote,info1:schlossPID,info2:codeType,info3:replyBiokey}
event63=User has been choosen two times{dev,remote,info1:schlossPID,info2:codeLink}
event64=Spezeiller Zutritt (Freigabe) Schloss 1 oder 2 und dann der Benutzer, welcher freigegeben wurde.
event64=Achtung, Doppelt vergeben. In der SL Version (Legic) für Österreich heißt das, das die Karte schon angelegt ist)
event65=User unlocked{dev,remote,info1:schlossPID}
event66=Program person via remote: The person has been registered properly{remote,info1:schlossPID}
event67=Program person via remote: PINs and code card were added successfully{remote,info1:schlossPID}
event68=TwinAlarm on/off{dev,bus,remote,info1:schlossPID,info2:twinalarm}
event69=Program person via remote: The TAN was entered wrong twice. It is necessary to register the person again{remote,info1:schlossPID}
event70=BAS disarmed{dev,bus,remote,info1:schlossPID}
event72=Disarming block activ{dev,bus,info1:schlossPID}
event73=Arming error{dev,bus,remote,info1:schlossPID,info2:errExtAlarmSystem}
event74=No BAS acknowledged{dev,bus,remote,info1:schlossPID}
event76=Threat alarm{dev,bus,remote,info1:schlossPID,info2:codeType,info3:finger}
event77=BAS armed{dev,bus,remote,info1:schlossPID}
event78=Time delay started{remote,info2:time,info3:Einheit}
event79=Time delay stoped{remote}
event80=Block period started{remote,info2:time,info3:Einheit}
event81=Block period stopped{remote}
event82=door open{remote,info2:time,info3:Einheit}
event87=Ignore bolt work switch
event89=TwinXT on/off{dev,bus,remote,info1:schlossPID,info2:twinExt}
event91=Lock has been registered{dev,bus,remote,info1:schlossPID}
event95=Motor step{dev,bus,remote,info1:schlossPID}
event98=New terminal
event100=Setup – error{dev,bus,remote,info1:schlossPID}
event102=Terminal – Reset{dev,bus,remote,info1:schlossPID}
event109=Terminal currentless
event110=Manipulation{dev,bus,remote,info1:schlossPID,info2:codeType,info3:replyBiokey}
event114=Sabotage
event119=Setup – error lock{dev,bus,remote,info1:schlossPID}
event122=Configuration invalid{info1:configError}
event123=Configuration imported
event124=Configuration exported
event126=Language has been choosen{remote,info1:schlossPID,info2:language,info3:languageId}
event127=Code card was read{info1:schlossPID}
event128=Code card registered{dev,remote,info1:schlossPID,info2:twinalarm}
event129=Code card unregistered{dev,remote,info1:schlossPID,info2:twinalarm}
event132=Card error{dev,bus,remote,info1:schlossPID,info2:errChipCard}
event143=Protocol export
event144=Low voltage{info1}
event148=Language imported{remote,info1:schlossPID,info2:language,info3:languageId}
event150=Finger registered{dev,bus,remote,info1:schlossPID,info2:finger,info3:twinalarm}
event152=Minuten changed{dev,bus,remote,info1:schlossPID,info2}
event153=Quality changed{dev,bus,remote,info1:schlossPID,info2}
event154=Safety changed{dev,bus,remote,info1:schlossPID,info2}
event155=Temperature changed{dev,bus,remote,info1:schlossPID,info2}
event158=Finger unregistered{dev,bus,remote,info1:schlossPID,info2:finger,info3:twinalarm}
event189=Motor error during opening{dev,bus,remote}
event192=Reply mistake{dev,bus,remote,info1:schlossPID,info2:replyDev}
event193=Bolt work middle{dev,remote}
event195=RTC – error read
event198=Communication Error{dev,bus,remote,info2:errComm}
event200=Motor error (close){dev,bus,remote}
event221=Speaker on/off{info2:speaker}
event222=Backround light on/off{info2:lighting}
event226=Serial number lock{dev,bus,remote,info1:schlossPID}
event227=Serial number not equal{dev,bus,remote}
event246=Alarm finger changed{dev,bus,remote,info1:schlossPID,info2:finger}

# Tabellen fuer Events

tab.schlossPIDFormat=Unser on position

tab.dev.0=TwinAlarm (0)
tab.dev.1=Lock 1 (1)
tab.dev.2=Lock 2 (2)
tab.dev.3=Lock 3 (3)
tab.dev.15=None (15)

tab.bus.0=None (0)
tab.bus.1=A (1)
tab.bus.2=B (2)
tab.bus.3=A and B (3)

tab.Einheit.2=sec (2)
tab.Einheit.3=min (3)
tab.Einheit.4=h (4)

tab.remote.0=Local (0)
tab.remote.1=Network (1)

tab.codeType.0=PIN-Code (0)
tab.codeType.1=Code card (1)
tab.codeType.2=Fingerprint (2)
tab.codeType.255=@NA (255)

tab.finger.0=left small Finger (0)
tab.finger.1=left Ring finger (1)
tab.finger.2=left middle finger (2)
tab.finger.3=left index finger (3)
tab.finger.4=left thumb (4)
tab.finger.5=right thumb (5)
tab.finger.6=right index finger (6)
tab.finger.7=right middle finger (7)
tab.finger.8=right ring finger (8)
tab.finger.9=right small finger (9)
tab.finger.255=no finger (255)

tab.replyBiokey.130=wrong or none sensor picture (130)
tab.replyBiokey.131=bad finger template (131)
tab.replyBiokey.132=Fingerprint – database is empty (132)
tab.replyBiokey.133=choosen user finger ID unknown (133)
tab.replyBiokey.134=unknown finger (134)
tab.replyBiokey.135=no sensor image received (135)
tab.replyBiokey.255=Biokey deactivated (255)

tab.errChipCard.0=read error (0)
tab.errChipCard.1=wrong card (1)
tab.errChipCard.2=error during reading the card (2)
tab.errChipCard.3=error during writing the card (3)
tab.errChipCard.4=error during reading the EEPROM (4)
tab.errChipCard.5=error during writing the EEPROM (5)
tab.errChipCard.6=error during reading the code card (6)
tab.errChipCard.255=no card error (255)

tab.errExtAlarmSystem.65=sent code is wrong (65)
tab.errExtAlarmSystem.66=no request from BAS received (66)
tab.errExtAlarmSystem.67=no request from BAS received during arming BAS (67)
tab.errExtAlarmSystem.68=Error during alarm output (68)
tab.errExtAlarmSystem.69=RS232 kommunikation error (69)
tab.errExtAlarmSystem.70=BAS not ready (70)
tab.errExtAlarmSystem.71=Disarming block aktiv (71)

tab.configError.2=open (2)
tab.configError.16=not enough user codes (16)
tab.configError.26=old code (26)
tab.configError.30=Parallel code and code linkage (30)
tab.configError.31=user new (31)
tab.configError.44=week program (44)
tab.configError.45=special days (45)
tab.configError.46=time delay (46)
tab.configError.47=locked time (47)
tab.configError.48=part locked time (48)
tab.configError.59=close & code (59)
tab.configError.76=silent alarm (76)
tab.configError.79=alarm- delay (79)
tab.configError.80=TwinAlarm and TwinXT (80)
tab.configError.90=door open (90)
tab.configError.152=locked time (152)
tab.configError.153=picture quality (153)
tab.configError.154=back, safety level (154)
tab.configError.155=temperature (155)
tab.configError.192=lock- error feedback (192)
tab.configError.198=lock- bus error feedback (198)
tab.configError.204=WTU – user (204)
tab.configError.208=time frame (208)

tab.replyDev.1=command was processed correctly (1)
tab.replyDev.2=command was not processed correctly (2)
tab.replyDev.7=send Device-ID (7)
tab.replyDev.14=request version of lock or alarmbox (14)
tab.replyDev.33=send number of registered users (33)
tab.replyDev.38=send open, closed or in between (38)
tab.replyDev.43=send number of registered code cards (43)
tab.replyDev.53=send lock release status (53)
tab.replyDev.73=lock activated silent alarm (73)

tab.twinalarm.0=on (0)
tab.twinalarm.1=off (1)

tab.twinExt.0=on (0)
tab.twinExt.1=off (1)

tab.codeLink.0=code linkage (0)
tab.codeLink.1=parallel code (1)

tab.language.0=no language prefered (0)
tab.language.1=german (1)
tab.language.2=english (2)
tab.language.3=francais (3)
tab.language.4=cesky (4)
tab.language.5=turkce (5)
tab.language.6=polski (6)
tab.language.7=suomi (7)
tab.language.8=expanol (8)
tab.language.9=portugues (9)
tab.language.10=nederlands (10)
tab.language.11=svenska (11)

tab.languageId.0=language slot 1 (0)
tab.languageId.1=langugae slot 2 (1)
tab.languageId.2=language slot 3 (2)

tab.errComm.0=send (0)
tab.errComm.1=receive (1)

tab.speaker.0=on (0)
tab.speaker.1=off (1)

tab.lighting.0=on (0)
tab.lighting.1=off (1)

tab.error.0=lock in use (F_BUSY)
tab.error.1=wrong telegram (F_TELEGRAM)
tab.error.2=unknown command (F_COMMAND)
tab.error.3=code number invalid (F_CODE)
tab.error.4=wrong user (F_USER)
tab.error.5=wrong Code (F_WRONGCODE)
tab.error.6=wrong time/date (F_RTCDATA)
tab.error.7=read / write error RTC (F_RTC)
tab.error.8=wrong user or user not authorized (F_AUTHENTICATION)
tab.error.9=wrong lock (F_SCHLOSS)
tab.error.10=outdated (F_PWID)
tab.error.11=wrong numbering of telegrams (F_NUM)
tab.error.12=wrong EEPROM in terminal (F_EEPROM)
tab.error.13=timeout (F_TIMEOUT)
tab.error.14=kommunikation error between terminal and lock system (F_COMSCHLOSS)
tab.error.15=terminal asks to terminate kommunikation (F_QUIT)

FLC Display-Texte